Back to Blog
Mazda toolbox5/6/2023 ![]() I figure 20 amp Level 2 charging isn’t worth all the hassle. 6.6 kW, 7.7 kW, and especially 11.5 kW (my new Bolt EUV’s max pull) are all out of the question unless I want to cause myself some serious relationship problems with El Paso Electric. I could probably get away with 20 amp Level 2 (4.8 kW), but that’s about all that would be safe. With only 80 amps coming in from the electric company, there’s just not much to spare for Level 2 charging. Why? Because I’m up against a pretty hard limit on the home’s electrical power. We actually never tripped the breaker, so I must’ve done something right.īut now, I own my own home, and I don’t have any convenient DIY janky options at my disposal. This meant that by the time it started pulling power, we would not only be in bed sleeping, but any load of laundry we had left drying would have also been done for hours. Sharing a circuit with my dryer may sound like a bad idea, but I set the charge timer so that it wouldn’t charge until 3AM. From the outside of the apartment, it didn’t look that bad. The property owner let me drill a small hole in the wall, which I then ran outside to the EVSE that came with the LEAF. Later, when I didn’t have a garage and I had my 2018 Nissan LEAF, I had to break open the plug for my dryer and add some extra wires for the car. This enabled me to make both trips every day without using any gas, and it only cost me around $50 to set it all up. Charging times for the Volt went from 8-10 hours down to around 3-4 (3.3 kW charging). I even had a convenient hole in the wall I could put the NEMA 14-50 plug into, so I did that, too. So, I broke out the soldering gun and cracked the case on the car’s L1 EVSE. I was taking a short highway drive twice daily that depleted the car’s charge, and there wasn’t enough time while the kids were at school for the car to get a full battery again. That was true for me for a few months.īut, with my Chevy Volt, I found that a change to my routine was forcing me to burn some gas every day. For many people, this is enough, and there’s no need for faster home charging. The obvious first move for a new EV owner is to just plug the car into a normal household outlet (aka Level 1). I’ve owned EVs and PHEVs for some time now, but I’ve used a lot of janky DIY charging setups over the years. The Things I’ve Done To Avoid Installing A Charging Station But, bailing wire, chewing gum, WD-40, duct tape, and JB Weld can only take you so far in life. Before it’s over, you’ll realize that I’m just a cheapskate lesbian with a decent toolbox and access to YouTube when I need to learn how to do something for myself. Well, let’s turn on Baba O’Riley by The Who and I’ll explain a bit about how I got here. “How could you be into EVs for so long and even work for CleanTechnica and not already have a professionally-installed Level 2 charging station at home?” As you start your navigation system, it will use the updated contents found on the SD card.“Wait a minute,” you may be thinking. ![]() ![]() Finally, remove your SD card and insert it into the SD card slot in your vehicle.When the installation is done, you can exit the Toolbox with the Exit button, or return to the main menu with the Home button.When the backup has been created, please wait until the files for the free update are downloaded and are transferred to your SD card.Note that this process can take several minutes. Please choose a name so that you can identify the backup later, then click on Backup to create it. Before installing the free update, it is strongly recommended that you backup the contents of your device, therefore Toolbox offers you the possibility to do so.If you would like to start the installation, click on the Install button. After successfully logging in, if there are free map updates available, you will be automatically offered to download them.Once your SD card has been recognized, you can login with your existing user account, or register a new account, if you do not yet have one.Please note that this process may take several minutes. Toolbox will recognize your connected SD card automatically.Remove the SD card from the SD slot in your vehicle and insert it into your PC.You can get your free map update easily and start using it in your car immediately. How to get my free map update in Mazda Toolbox
0 Comments
Read More
Leave a Reply. |